EMP-Centauri MS13/6PIU-6 DiSEqC multiswitch
EMP-Centauri MS13/6PIU-6 DiSEqC multiswitch
€199.00
€164.46
Quick delivery
- Free shipment NL / BE (orders above EUR 50.00)
- 30 days withdrawal period
- Pick-up at store in Nieuwegein (NL) is possible
- Ordered before 16.00 hours, often same day shipped
Product description
DiSEqC multiswitch with 13 inputs and 6 outputs and integrated power supply. Suitable for receiving 3 satellites (12 polarizations), where you can choose between the distribution of the (active or passive) terrestrial or satellite signal from 3 satellite positions to a maximum of 26 participants. The multiswitch is compatible with all satellite receivers that support the DiSEqC system. The multiswitches with integrated power supplies are designed for maximum efficiency during use, eliminating the need for a stand-by mode.
- Multiswitches are operated from the satellite receiver with analog and DiSEqC commands. In the receiver's configuration menu, the LNB type must be set to "Universal" and the differentiation between the satellites to be received is done using the DiSEqC 1/2/3 (A / B / C) parameter.
- Multiswitches are not compatible with Monoblock LNB's.
- If a higher number of outputs is needed than available, two multiswitches should be placed instead of one. The routing of the LNB outputs should be done using signal splitters.
- If the terrestrial band is used, all unused outputs should be turned off using a 75 Ohm load.
- Switching between the active and passive terrestrial band is possible by turning the attenuator at the terrestrial input counter-clockwise.
- The 22 KHz tone required for Quad LNB support can be turned off via a DIP-switch.
- The DC power supply for the preamplifier of the terrestrial antenna is limited to 150 mA max.. The power supply is interrupted if a higher load or short circuit occurs at the terrestrial input. To minimize power consumption, it is recommended to connect an external DC block if a short circuit occurs at the terrestrial input.
Benefits of PROFI CLASS multiswitches:
- Input attenuators on all inputs
- Configurable support for Quad LNB's
- Selective active / passive processing of terrestrial band
- 12V DC power supply for terrestrial preamplifier
- Extended temperature range
Features of EMP-Centauri MS13/6PIU-6 DiSEqC PROFI CLASS multiswitch
| Number of inputs: | 13 |
| Number of outputs: | 6 |
| Quad LNB support: | Yes |
| Input attenuators: | Yes |
| Terrestrial input: | active / passive |
| 12V DC power supply for terrestrial preamplifier: | Yes |
| Power supply: | Internal |
| Warranty: | 4 years |
Specifications EMP-Centauri MS13/6PIU-6 DiSEqC PROFI CLASS multiswitch
| Number of inputs: | 13 |
| Number of outputs: | 6 |
| Frequency range SAT: | 950-2300 MHz |
| Frequency range TER (active): | 40-862 MHz |
| Frequency range TER (passive): | 5-862 MHz |
| Insertion loss SAT (average): | - dB |
| Insertion loss TER (active / average): | - dB |
| Insertion loss TER (passive / average): | - dB |
| Isolation between V/H & LH bands (min): | 20 dB |
| Isolation between LNB's (min): | 25 dB |
| Maximum input level SAT (average): | 90 dBuV |
| Maximum input level TER (active / average): | 90 dBuV |
| Maximum input level TER (passive / average): | 100 dBuV |
| Maximum output level SAT (average): | 90 dBuV |
| Maximum output level TER (active / average): | - dBuV |
| Maximum input level TER (passive / average): | - dBuV |
| Power consumption of each receiver (18V): | 75 mA |
| Power consumption of internal power supply, TER (active): | 6.5 W |
| Power consumption of internal power supply, TER (passive): | 4.5 W |
| Dimensions (L x W x H): | 470 x 152 x 87 mm |
| Temperature range: | -30 to +70 C |
| SKU | 72357 |
|---|---|
| Number of satellites | 3 |
| Brand | EMP-centauri |
| Multiswitch type | Multiswitch |
| Voeding | Internal |
Reviews
Write Your Own Review
