EMP-Centauri MS13/26PIU-6 DiSEqC multiswitch
EMP-Centauri MS13/26PIU-6 DiSEqC multiswitch
€419.00
€346.28
Quick delivery
- Free shipment NL / BE (orders above EUR 50.00)
- 30 days withdrawal period
- Pick-up at store in Nieuwegein (NL) is possible
- Ordered before 16.00 hours, often same day shipped
Product description
DiSEqC multiswitch with 13 inputs and 26 outputs and integrated power supply. Suitable for reception of 3 satellites (12 polarizations), where one can choose between distribution of the (active or passive) terrestrial or satellite signal from 3 satellite positions to up to 26 subscribers. The multiswitch is compatible with all satellite receivers that support the DiSEqC system. Multiswitches with integrated power supplies are designed for maximum efficiency during operation, eliminating the need for a standby mode.
- Multiswitches are controlled from the satellite receiver with analog and DiSEqC commands. In the configuration menu of the receiver, the LNB type should be set to "Universal" and the differentiation between the satellites to be received through the DiSEqC 1/2/3 (A / B / C) parameter.
- Multiswitches are not compatible with Monoblock LNBs.
- If a higher number of outputs is required than available, two multiswitches should be installed instead of one. The routing of the LNB outputs should be done using signal splitters.
- If the terrestrial band is used, all unused outputs should be switched off using a 75 Ohm load.
- Switching between the active and passive terrestrial band is possible by turning the attenuator at the terrestrial input counterclockwise.
- The 22 KHz tone required for Quad LNB support can be disabled via a DIP switch.
- The DC power supply for the terrestrial antenna preamplifier is limited to 150 mA max. The power supply is disconnected if a higher load or short circuit occurs on the terrestrial input. To minimize power consumption, it is recommended that an external DC block be connected if a short circuit occurs on the terrestrial input.
Advantages PROFI CLASS multiswitches:
- Input attenuators on all inputs
- Configurable support for Quad LNBs
- Selective active / passive processing of terrestrial band
- 12V DC power supply for terrestrial pre-amplifier
- Extended temperature range
Features EMP-Centauri MS13/26PIU-6 DiSEqC PROFI CLASS multiswitch
| Number of inputs: | 13 |
| Number of outputs: | 26 |
| Quad LNB support: | Yes |
| Input attenuators: | Yes |
| Terrestrial input: | active / passive |
| 12V DC power supply for terrestrial preamplifier: | Yes |
| Power supply: | Internal |
| Warranty: | 4 years |
Specifications EMP-Centauri MS13/26PIU-6 DiSEqC PROFI CLASS multiswitch
| Number of inputs: | 13 |
| Number of outputs: | 26 |
| Frequency range SAT: | 950-2300 MHz |
| Frequency range TER (active): | 40-862 MHz |
| Frequency range TER (passive): | 5-862 MHz |
| Insertion loss SAT (average): | 5 dB |
| Insertion loss TER (active/average): | 10 dB |
| Insertion loss TER (passive/average): | 25 dB |
| Isolation between V/H & LH bands (min): | 20 dB |
| Isolation between LNBs (min): | 25 dB |
| Maximum input level SAT (average): | 90 dBuV |
| Maximum input level TER (active / average): | 90 dBuV |
| Maximum input level TER (passive / average): | 100 dBuV |
| Maximum output level SAT (average): | 85 dBuV |
| Maximum output level TER (active / average): | 80 dBuV |
| Maximum input level TER (passive / average): | 75 dBuV |
| Current consumption of each receiver (18V): | 75 mA |
| Current consumption of internal power supply, TER (active): | 6.5 W |
| Current consumption of internal power supply, TER (passive): | 4.5 W |
| Dimensions (L x W x H): | 470 x 152 x 87 mm |
| Temperature range: | -30 to +70 C |
| SKU | 72362 |
|---|---|
| Number of satellites | 3 |
| Brand | EMP-centauri |
| Multiswitch type | Multiswitch |
| Voeding | Internal |
Reviews
Write Your Own Review
